E6000 Industrial Adhesive
E6000 is formulated to meet high performance industrial requirements. The self-leveling formula forms a powerful bond with most any material and will remain flexible once cured. E6000 Industrial will handle just about any project DIYers or PROs throw at it!
- Tough – 2X stronger and 60X more flex than Polyurethane!
- Non-flammable once cured
- Chemical resistant – safe for applications exposed to dilute acids and dilute caustics
- Waterproof – can be submerged in fresh and salt water after complete cure
- Paintable – paint to match surrounding area to make UV-resistant
- Temperature resistant – unaffected by extreme heat or cold once cured
- Flexible – excellent for bonding items subject to vibration
|Sizes Available:||1.0 fl oz, 3.7 fl oz, 10.2 fl oz,|
|Gallon, 5 Gallon, Drum|
|Color:||Clear, Black (3.7 oz and 10.2 oz only)|
WARNING: This product can expose you to chemicals including perchloroethylene which is known to the State of California to cause cancer. For more information go to www.p65warnings.ca.gov.
INSTRUCTIONS FOR SAFE USE
Follow these step-by-step directions when using E6000:
Read directions and test small area before use.
1. Surface should be clean, dry and free of dirt. For best results, lightly roughen surface before use.
2. TUBE: Puncture inner seal using pointer cap (if tube has a foil seal). CARTRIDGE: Trim end of nozzle. Puncture inner seal. Ideal application temperature range is 50 to 90 °F (10 to 32 °C). However, fully cured adhesive can withstand temperatures from 40 to 180 °F (-40 to 82 °C) intermittently.
3. Apply directly to surfaces to be bonded or repaired.
4. Allow 24 hours for curing--Maximum bond strength may not be reached for up to 72 hours.
5. TUBE: For future easy cap removal, apply a thin coat of petroleum jelly to the threads of the tube before replacing the cap. CARTRIDGE: For prolonged storage after opening, cover or plug the opening of the nozzle.
6. Clean uncured adhesive with acetone or citrus-based solvents.
Product is paintable and immediately resistant to precipitation upon application.
Note: May damage finished surfaces. Avoid such contact until completely dry. Not recommended for use on polystyrene, polyethylene, polypropylene, Styrofoam™ or paper products.
SAFETY DATA SHEET
SDS SHEET REQUESTS: To request an SDS, please use the below link and include the following information
- Product name and description.
- Product Sales Part Number or UPC (if available).
- Product color.
- Country of usage.
- Language desired.
SDS Request Email Link: firstname.lastname@example.org
TECHNICAL DATA SHEET
What temperature range does E6000 withstand?
E6000 can be applied in temperatures ranging from 50 °F to 90 °F (10 °C to 32 °C). When cured, E6000 can withstand temperatures between -40 °F and 180 °F (-40 °C and 82 °C).
Is E6000 UV resistant?
E6000 may be painted over for maximum UV resistance. Clear E6000 is not formulated for exposure to sunlight.
Can E6000 be used on Styrofoam™?
No. E6000 is also not recommended for use on any polystyrene, polyethylene or polypropylene plastics.
Will E6000 crack or break under stress?
No, E6000 dries to a rubber-like consistency that is flexible and moves with adhered material.
How long does E6000 take to dry?
E6000 starts getting tacky in approximately 2 minutes and begins setting in approximately 10 minutes. A full cure takes between 24 and 72 hours.
Remember, temperature and humidity will affect dry time. To speed drying, apply heat using a handheld dryer set on low. Do not hold heat directly on E6000.
What is used to clean up uncured E6000?
Small amounts of acetone or citrus-based solvents for uncured E6000. Cured E6000 may be removed by cutting and scraping.
300 dpi / RGB / actual size
150 dpi / RGB / 4 inch|600 pixels (H)
|E6000 59.1 mL Carded Tube - Clear 300 dpi CA||E6000 59.1 mL Carded Tube - Clear 150 dpi CA|
|E6000 109.4 mL Carded Tube - Clear 300 dpi CA||E6000 109.4 mL Carded Tube - Clear 150 dpi CA|
|E6000 301.6 mL Cartridge - Clear 300 dpi CA||E6000 301.6 mL Cartridge - Clear 150 dpi CA|