E6100 Industrial Adhesive

E6100 has all of the strength of E6000 but this non-sag formulation won’t slump or run and allows for maximum control. It’s a perfect choice for overhead and vertical applications when nails just won’t work.

  • Non-slump – won’t sag, drip or run on vertical or horizontal applications 
  • Tough – 2X stronger and 60X more flex than Polyurethane! 
  • Non-flammable once cured 
  • Chemical resistant – safe for applications exposed to dilute acids and dilute caustics 
  • Waterproof – can be submerged in fresh and salt water after complete cure 
  • Paintable – paint to match surrounding area or make UV-resistant 
  • Temperature resistant – unaffected by extreme heat or cold once cured 
  • Flexible – excellent for bonding items subject to vibration 
WARNING: This product can expose you to chemicals including perchloroethylene which is known to the State of California to cause cancer. For more information go to www.p65warnings.ca.gov.

INSTRUCTIONS

Follow these step-by-step directions when using E6100: 

Read directions and test small area before use.

  1. Surface should be clean, dry and free of dirt. For best results, lightly roughen surface before use.
  2. Trim end of nozzle. Puncture inner seal. Ideal application temperature range is 50 to 90 °F (10 to 32 °C). However, fully cured adhesive can withstand temperatures from 40 to 180 °F (-40 to 82 °C) intermittently.
  3. Apply directly to surfaces to be bonded or repaired.
  4. Allow 24 hours for curing–Maximum bond strength may not be reached for up to 72 hours.
  5. For prolonged storage after opening, cover or plug the opening of the nozzle.
  6. Clean uncured adhesive with acetone or citrus-based solvents. Cured material may be removed by cutting or scraping.

Product is paintable and immediately resistant to precipitation upon application.

PRODUCT SPECS

Sizes Available: 10.2 oz, Gallon, 5 Gallon, Drum
Color: Clear, Black (10.2 oz only), Gray (10.2 oz only), White (10.2 oz only)

WARNING: This product can expose you to chemicals including perchloroethylene which is known to the State of California to cause cancer. For more information go to www.p65warnings.ca.gov.

DATA SHEETS

SAFETY DATA SHEET

SDS SHEET REQUESTS:  To request an SDS, please use the below link and include the following information

  • Product name and description.
  • Product Sales Part Number or UPC (if available).
  • Product color.
  • Country of usage.
  • Language desired.

SDS Request Email Link:  sds@eclecticproducts.com

TECHNICAL DATA SHEET

US, Canadian, Mexico – English document (Clear) (English)
US, Canadian, Mexico – English document (Black, Gray & White) (English)

 

FAQS

What temperature range does E6100 withstand?
E6100 can be applied in temperatures ranging from 50 °F to 90 °F (10 °C to 32 °C). Once cured, E1000 can withstand temperatures between -40 °F and 180 °F (-40 °C to 82 °C).

Is E6100 UV resistant?
E6100 may be painted over for maximum UV resistance. Clear E6100 is not formulated for exposure to sunlight.

Can E6100 be used on Styrofoam™?
No. E6100 is also not recommended for use on any polystyrene, polyethylene or polypropylene plastics.

Will E6100 crack or break under stress?
No, E6100 dries to a rubber-like consistency that is flexible and moves with adhered material.

How long does E6100 take to dry?
E6100 starts getting tacky in approximately 2 minutes and begins setting in approximately 10 minutes. A full cure takes between 24 and 72 hours.

Remember, temperature and humidity will affect dry time. To speed drying, apply heat using a handheld dryer set on low. Do not hold heat directly on E6100.

What is used to clean up uncured E6100?
Small amounts of acetone or citrus-based solvents for uncured E6100. Cured E6100 may be removed by cutting and scraping.

Where to Buy

Please check your local store for product availability.