E6800 Industrial Adhesive

E6800 has all the adhesion power of E6000 but the formula is enhanced with UV stabilizers. It is ideal for outdoor applications. E6800 easily bonds to fiberglass, concrete, metal, glass, wood and more!

  • UV resistant – resists yellowing and cracking when used outdoors 
  • Tough – 2X stronger and 60X more flex than Polyurethane! 
  • Non-flammable once cured 
  • Chemical resistant – safe for applications exposed to dilute acids and dilute caustics 
  • Waterproof – can be submerged in fresh and salt water after complete cure 
  • Paintable – paint to match surrounding area 
  • Temperature resistant – unaffected by extreme heat or cold once cured 
  • Flexible – excellent for bonding items subject to vibration 
WARNING: This product can expose you to chemicals including perchloroethylene which is known to the State of California to cause cancer. For more information go to www.p65warnings.ca.gov.

INSTRUCTIONS

Follow these step-by-step directions when using E6800: 

Read directions and test small area before use.

  1. Surface should be clean, dry and free of dirt. For best results, lightly roughen surface before use.
  2. TUBE: Puncture inner seal using pointer cap (if tube has a foil seal). CARTRIDGE: Trim end of nozzle. Puncture inner seal. Ideal application temperature range is 50 to 90 °F (10 to 32 °C). However, fully cured adhesive can withstand temperatures from 40 to 180 °F (-40 to 82 °C) intermittently.
  3. Apply directly to surfaces to be bonded or repaired.
  4. Allow 24 hours for curing–Maximum bond strength may not be reached for up to 72 hours.
  5. TUBE: For future easy cap removal, apply a thin coat of petroleum jelly to the threads of the tube before replacing the cap. CARTRIDGE: For prolonged storage after opening, cover or plug the opening of the nozzle.
  6. Clean uncured adhesive with acetone or citrus-based solvents.
    Product is paintable and immediately resistant to precipitation upon application.

Product is paintable and immediately resistant to precipitation upon application.

PRODUCT SPECS

Sizes Available: 3.7 fl oz, 10.2 fl oz, Gallon, 5 Gallon, Drum
Color: Clear

WARNING: This product can expose you to chemicals including perchloroethylene which is known to the State of California to cause cancer. For more information go to www.p65warnings.ca.gov.

DATA SHEETS

SAFETY DATA SHEET

SDS SHEET REQUESTS:  To request an SDS, please use the below link and include the following information

  • Product name and description.
  • Product Sales Part Number or UPC (if available).
  • Product color.
  • Country of usage.
  • Language desired.

SDS Request Email Link:  sds@eclecticproducts.com

TECHNICAL DATA SHEET

US English document (Clear)-E6800 INDUSTRIAL ADHESIVE (English)

 

FAQS

What temperature range does E6800 withstand?
E6800 can be applied in temperatures ranging from 50 °F to 90 °F (10 °C to 32 °C). Once cured, E6800 can withstand temperatures between -40 °F and 180 °F (-40 °C and 82 °C).

Is E6800 UV resistant?
Yes.

Can E6800 be used on Styrofoam™?
No, E6800 is also not recommended for use on any polystyrene, polyethylene or polypropylene plastics.

Will E6800 crack or break under stress?
No, E6800 dries to a rubber-like consistency that is flexible and moves with adhered material.

How long does E6800 take to cure?
E6800 starts getting tacky in approximately 2 minutes and begins setting in approximately 10 minutes. A full cure takes between 24 and 72 hours.

Remember, temperature and humidity will affect cure time. To speed drying, apply heat using a handheld dryer set on low. Do not hold heat directly on E6800.

What is used to clean up uncured E6800?
Small amounts of acetone or citrus-based solvents for uncured E6800. Cured E6800 may be removed by cutting and scraping.

Where to Buy

Please check your local store for product availability.